366-8821 20R-2323 CAT Computer Board Controller ECU Caterpillar

280-3264: CONTROL & MTG GP-ENGINE ELEK
CONTROL & MTG GP-ENGINE ELEK
280-3264 CONTROL & MTG GP-ENGINE ELEK
S/N C4H1-UP; RJK1-UP
PART OF 267-5125, 267-5126 CHASSIS AR
2803264 CONTROL & MTG GP-ENGINE ELEK Parts scheme
For full view, you need register
Parts for your 325D MH EXCAVATOR:
CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 366-8821 [1] CONTROL GP-UNPROGRAMMED (ENGINE ELECTRONIC)
2. 9X-2480 M [4] BOLT (M6X1X45-MM)
3. 9X-8256 [4] WASHER (6.6X12X2-MM THK)
M METRIC PART
R REMANUFACTURED PART MAY BE AVAILABLE

#SEBP45040201

205-6343: CONTROL GP-HYDRAULIC GENERATOR
CONTROL GP-HYDRAULIC GENERATOR
205-6343 CONTROL GP-HYDRAULIC GENERATOR
S/N C4H1-UP; RJK1-UP
PART OF 273-6546, 273-7254 GENERATOR GP-HYDRAULIC
FIELD REPLACEMENT ORDER @@@@@318-9582@@@@@, @@@@@318-9583@@@@@, @@@@@318-9584@@@@@
AN ATTACHMENT
2056343 CONTROL GP-HYDRAULIC GENERATOR Parts scheme 2056343 CONTROL GP-HYDRAULIC GENERATOR Parts scheme

Parts for your 325D MH EXCAVATOR:
CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 173-4441 [1] ENCLOSURE
2. 173-5432 [1] PANEL
3. 230-7662 C [1] CONTROL GP-HYDRAULIC GENERATOR
4. [1] CONVERTER
5. [1] ELEMENT (HEAT)
6. 178-3339 [10] SCREW (8-32X0.5-IN)
7. 219-0370 [3] STRIP-TERMINAL
8. [1] THERMOSTAT
9. 160-3600 [1] RELAY (LIFT RELAY ONE)
9A. 160-3600 [1] RELAY (LIFT RELAY TWO)
9B. 160-3600 [1] RELAY (DROP RELAY ONE)
9C. 160-3600 [1] RELAY (DROP RELAY TWO)
10. 222-6983 [2] HEAT SINK
11. 178-3341 [4] SCREW (8-32X2-IN)
12. 9S-2544 [18] SCREW-HEX HEAD (8-32X11.13-MM)
13. 097-5921 [1] RAIL-MOUNTING
14. [6] BRACKET
15. 5M-9695 [8] SCREW (6-32X0.312-IN)
16. 160-3603 [1] RELAY (BOOST)
17. 178-3340 [4] SCREW (1/4-20-THD)
18. [1] MONITOR
19. 160-3610 [1] CONNECTOR AS
20. 180-7050 [1] CLAMP
21. 160-3604 [1] RELAY (VOLTAGE, GENERATOR)
22. 160-3606 [1] CONNECTOR AS
23. 173-5450 [1] SPRING
24. 160-3602 [1] TIMER
25. 173-5455 [1] SOCKET-RELAY
26. 173-5456 [1] CLIP
27. 283-4308 [4] END-STOP
28. 216-0244 [1] TRANSDUCER
29. 173-5433 [1] BASE
30. 178-3342 [2] SCREW
31. [1] BASE
32. [2] FUSE (30-AMPERE)
33. 173-5451 [1] CONTACT
34. [1] BLOCK-TERMINAL
35. [1] BLOCK-TERMINAL
36. 160-3596 [1] RESISTOR
37. 173-5462 [1] RESISTOR
38. 5S-7349 [4] BOLT (1/4-20X0.5-IN)
39. 6V-8185 [4] NUT (1/4-20-THD)
40. 5P-4115 [4] WASHER-HARD (7.2X19X2-MM THK)
41. 160-3580 [1] HANDLE
42. 160-3581 [1] SHAFT AS
43. 173-5436 [1] FUSE (1-AMPERE)
44. 201-9909 [3] FUSE (5-AMPERE)
45. [4] HOLDER AS-FUSE
46. 219-0371 [1] STRIP-TERMINAL
47. 180-7090 [2] CONNECTOR
48. 173-5439 [4] TERMINAL
49. 173-5441 [1] PLATE
50. 203-2534 [1] BASE-MOUNTING
51. 207-7013 [1] HARNESS AS-PANEL
52. 180-5557 [1] HARNESS AS-WIRING (MAGNET CIRCUIT)
103-8133 [1] KIT-RECEPTACLE (12-PIN)
(INCLUDES RECEPTACLE AS & WEDGE)
53. 180-7047 [1] HARNESS AS-POWER (DC)
54. 180-7096 [1] HARNESS AS-POWER (RESISTOR)
55. 160-3579 [1] SWITCH (DISCONNECT)
56. 173-5440 [26] TERMINAL
57. 190-3816 [2] PLATE-END
58. 180-5556 [1] ENCLOSURE
59. 180-5558 [1] PANEL
60. 178-3343 [2] SCREW
61. 4B-2043 [2] NUT (8-32-THD)
62. 180-7052 [2] STANDOFF
63. 5P-8937 B COMPOUND-JOINT (THERMAL)
64. 4B-4863 [2] WASHER (4.7X11X1.2-MM THK)
65. 3B-4501 [2] LOCKWASHER
66. 180-7089 [3] CONNECTOR
67. 219-4209 [1] JUMPER-STRIP
68. 205-8375 [1] WIRE AS
69. 205-8374 [2] SUPPRESSOR AS
(EACH INCLUDES)
125-7874 E TUBE-HEAT SHRINK (5.72-MM DIA)(6-CM)
70. 3L-9089 [2] SCREW-FORMING
71. 9Y-7207 [1] STRIP-TERMINAL
72. 4B-2047 [2] NUT (10-24-THD)
73. 7M-9910 [2] SCREW-MACHINE (10-24X1-IN)
74. 008-9792 [2] SCREW-WASHER HEAD (1/4-20X0.5-IN)
75. 201-9910 [1] STRIP
76. [2] STRIP
77. [2] STRIP
78. [2] STRIP
79. [1] CABLE
80. 123-6574 [3] BUSHING
81. 180-7093 [2] CONNECTOR
82. 9M-4494 [3] NUT-SPANNER (3/4-14 NPT-THD)
83. 095-0741 M [2] SCREW-MACHINE (M6X1-THD)
84. 017-8715 [2] SCREW-SELF-TAPPING
85. 8S-4626 [2] SPLICE-WIRE
86. 117-9409 [1] GROMMET
87. 229-6611 [1] DIODE AS
B USE AS REQUIRED
C CHANGE FROM PREVIOUS TYPE
E ORDER BY THE CENTIMETER
M METRIC PART

#SEBP45040202

318-9582: CONTROL GP-HYDRAULIC GENERATOR
CONTROL GP-HYDRAULIC GENERATOR
318-9582 CONTROL GP-HYDRAULIC GENERATOR -15-KW
S/N C4H1-UP; RJK1-UP
FIELD REPLACEMENT FOR @@@@@205-6343@@@@@
3189582 CONTROL GP-HYDRAULIC GENERATOR Parts scheme 3189582 CONTROL GP-HYDRAULIC GENERATOR Parts scheme

Parts for your 325D MH EXCAVATOR:
CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4P-4890 [1] NUT-SPECIAL (1/2-14-THD)
2. 7K-1181 [6] STRAP-CABLE
3. 8J-1256 [1] CLIP
4. 8W-4756 [1] BUSHING-TERMINAL
5. 062-5388 [2] LOCKNUT (1-11-1/2-THD)
6. 068-3708 [1] LOCKNUT (1-11-1/4-THD)
7. 104-3648 [1] BUSHING
8. 104-3650 [1] BUSHING
9. 135-1669 [2] CONNECTOR (MALE)
10. 135-1670 [2] CONNECTOR (FEMALE)
11. 171-4667 [1] COVER
12. 178-3339 [4] SCREW (8-32X0.5-IN)
13. 180-7113 [1] CONNECTOR
14. 190-9372 [1] CONNECTOR
15. 199-9107 [1] FUSE AS (70-AMPERE)
190-9393 [1] ADAPTER
190-9551 [1] FUSE (70-AMPERE)
16. 289-3972 Y [1] PANEL GP-CONTROL
17. 317-7370 [1] CONNECTOR
18. 317-9124 [1] CABLE AS
2L-8052 [2] TERMINAL-RING (6-GA, 3/8-IN SCREW)
-OR-
2L-8060 [2] TERMINAL-RING (8-GA, 3/8-IN SCREW)
19. 317-9128 [1] HARNESS AS-BOX
3N-9711 [2] CONNECTOR
5P-0765 E HOSE (5-CM)
5P-1276 E CONDUIT (26.5-MM ID)(125-CM)
2L-8052 [3] TERMINAL-RING (6-GA, 3/8-IN SCREW)
8L-8413 [2] STRAP-CABLE (WHITE)
20. 325-8271 [1] HARNESS AS-PANEL
8T-8737 [8] PLUG-SEAL
9X-3402 [10] SOCKET-CONNECTOR (16-GA TO 18-GA)
-OR-
126-1768 [10] SOCKET-CONNECTOR (14-GA TO 16-GA)
2L-8076 [6] TERMINAL-RING (14-GA TO 16-GA, NO. 10 SCREW)
172-6062 [1] PLUG AS-CONNECTOR (18-PIN)
172-6065 [1] WEDGE-PLUG LOCK
21. 347-0570 [1] MONITOR
22. 202-2762 [2] CLIP
23. 4B-2043 [4] NUT (8-32-THD)
24. 4B-4863 [8] WASHER (4.7X11X1.2-MM THK)
25. 4D-7388 [1] CLIP
26. 5C-2890 M [7] NUT (M6X1-THD)
27. 5C-9553 M [7] BOLT (M6X1X16-MM)
28. 6V-7744 M [3] LOCKNUT (M10X1.5-THD)
29. 7X-7729 [1] WASHER (11X25X3-MM THK)
30. 8C-9660 [2] WASHER (4.6X7.9X0.8-MM THK)
31. 8T-4121 [12] WASHER-HARD (11X21X2.5-MM THK)
32. 8T-4133 M [2] NUT (M10X1.5-THD)
33. 8T-4137 M [2] BOLT (M10X1.5X20-MM)
34. 8T-4185 M [3] BOLT (M10X1.5X50-MM)
35. 8T-4195 M [2] BOLT (M10X1.5X30-MM)
36. 8T-4205 [10] WASHER-HARD (7.2X14.5X2-MM THK)
37. 8T-6466 M [1] BOLT (M10X1.5X60-MM)
38. 8T-9405 M [2] BOLT-SOCKET HEAD (M4X0.7X16-MM)
39. 9X-8402 [1] CLIP
E ORDER BY THE CENTIMETER
M METRIC PART
Y SEPARATE ILLUSTRATION

#SEBP45040203

318-9583: CONTROL GP-HYDRAULIC GENERATOR
CONTROL GP-HYDRAULIC GENERATOR
318-9583 CONTROL GP-HYDRAULIC GENERATOR -20-KW
S/N C4H1-UP; RJK1-UP
FIELD REPLACEMENT FOR @@@@@205-6343@@@@@
3189583 CONTROL GP-HYDRAULIC GENERATOR Parts scheme 3189583 CONTROL GP-HYDRAULIC GENERATOR Parts scheme

Parts for your 325D MH EXCAVATOR:
CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4P-4890 [1] NUT-SPECIAL (1/2-14-THD)
2. 7K-1181 [6] STRAP-CABLE
3. 8J-1256 [1] CLIP
4. 8W-4756 [1] BUSHING-TERMINAL
5. 062-5388 [2] LOCKNUT (1-11-1/2-THD)
6. 068-3708 [1] LOCKNUT (1-11-1/4-THD)
7. 104-3648 [1] BUSHING
8. 104-3650 [1] BUSHING
9. 135-1669 [2] CONNECTOR (MALE)
10. 135-1670 [2] CONNECTOR (FEMALE)
11. 171-4667 [1] COVER
12. 178-3339 [4] SCREW (8-32X0.5-IN)
13. 180-7113 [1] CONNECTOR
14. 190-9372 [1] CONNECTOR
15. 289-3972 Y [1] PANEL GP-CONTROL
16. 317-7370 [1] CONNECTOR
17. 317-9124 [1] CABLE AS
2L-8052 [2] TERMINAL-RING (6-GA, 3/8-IN SCREW)
-OR-
2L-8060 [2] TERMINAL-RING (8-GA, 3/8-IN SCREW)
18. 317-9128 [1] HARNESS AS-BOX
5P-1276 E CONDUIT (26.5-MM ID)(125-CM)
3N-9711 [2] CONNECTOR
5P-0765 E HOSE (5-CM)
8L-8413 [2] STRAP-CABLE (WHITE)
6H-3587 [3] TERMINAL-RING (6-GA TO 8-GA, 3/8-IN SCREW)
19. 323-2194 [1] FUSE AS (90-AMPERE)
190-9393 [1] ADAPTER
323-2192 [1] FUSE (90-AMPERE)
20. 347-0570 [1] MONITOR
21. 202-2762 [2] CLIP
22. 325-8271 [1] HARNESS AS-PANEL
172-6062 [1] PLUG AS-CONNECTOR (18-PIN)
8T-8737 [8] PLUG-SEAL
126-1768 [10] SOCKET-CONNECTOR (14-GA TO 16-GA)
-OR-
9X-3402 [10] SOCKET-CONNECTOR (16-GA TO 18-GA)
2L-8076 [6] TERMINAL-RING (14-GA TO 16-GA, NO. 10 SCREW)
23. 4B-2043 [4] NUT (8-32-THD)
24. 4B-4863 [8] WASHER (4.7X11X1.2-MM THK)
25. 4D-7388 [2] CLIP
26. 5C-2890 M [7] NUT (M6X1-THD)
27. 5C-9553 M [7] BOLT (M6X1X16-MM)
28. 6V-7744 M [3] LOCKNUT (M10X1.5-THD)
29. 8C-9660 [2] WASHER (4.6X7.9X0.8-MM THK)
30. 8T-4121 [13] WASHER-HARD (11X21X2.5-MM THK)
31. 8T-4133 M [2] NUT (M10X1.5-THD)
32. 8T-4137 M [2] BOLT (M10X1.5X20-MM)
33. 8T-4185 M [3] BOLT (M10X1.5X50-MM)
34. 8T-4195 M [2] BOLT (M10X1.5X30-MM)
35. 8T-4205 [10] WASHER-HARD (7.2X14.5X2-MM THK)
36. 8T-6466 M [1] BOLT (M10X1.5X60-MM)
37. 8T-9405 M [2] BOLT-SOCKET HEAD (M4X0.7X16-MM)